United Security Products AVD-45c Dokumentacja Pobierz pdf (Strona 2)

22650 County Highway 6

P.O. Box 1708

Detroit Lakes, Minnesota 56502 USA

1-888-DIAL-SJE (1-888-342-5753)

Phone: 218-847-1317

Fax: 218-847-4617

E-mail: [email protected]

©SJE-Rhombus Printed in USA 03/03

INSTALLING THE AUTO DIALER

ELECTRICAL SHOCK HAZARD

Disconnect power before installing or servicing this

product. A qualified service person must install and

service this product according to applicable electrical

and plumbing codes.

EXPLOSION OR FIRE HAZARD

Do not use this product with flammable liquids.

Do not install in hazardous locations as defined by

National Electrical Code, ANSI/NFPA 70.

Failure to follow these precautions could result in serious injury or death. Replace product immediately if switch cable becomes damaged

or severed. Keep these instructions with warranty after installation. This product must be installed in accordance with National Electric Code,

ANSI/NFPA 70 so as to prevent moisture from entering or accumulating within boxes, conduit bodies, fittings, float housing, or cable.

TESTING THE AUTO DIALER

PROGRAMMING THE AUTO DIALER

PROGRAMMING TIPS

FIGURE A

TWO NORMALLY CLOSED CONTACTS

FIGURE B

TWO NORMALLY OPEN CONTACTS

Note: Temperature switch can also be used by itself.

See Figure C.

FIGURE C

Note: These instructions are intended as a quick reference for the

most common installation of the Auto Dialer when used with a

control panel. For complete instructions, see the included

Installation and Instruction Manual for the Automatic Voice

Dialer. Before beginning installation, read the entire instruction

manual for the AVD-45b Automatic Voice Dialer.

1. Determine indoor mounting location for the Auto Dialer.

2. If mounting the Auto Dialer to the wall, use the two supplied

screws. Install the screws parallel and level 5 3/16 inches apart.

3. Install the four conductor power/alarm cable into a control panel

using only the white and yellow conductors. The conductors can

be attached to normally open or normally closed contacts. Note:

Trim the red and black conductors flush with outer jacket of the

cable. (See Figures A & B for optional wiring methods.)

4. Install the two conductor telephone cable by matching the appropriate

colors to a telephone service or by installing an appropriate

connector.

5. Install the 9 VDC battery if backup power is desired. Note: The

battery will supply approximately four hours of backup power.

Replace battery yearly and after each power outage.

6. Hang the auto dialer on the two mounting screws previously

installed.

7. Connect the phone cable and power/alarm cable to the auto dialer

using the supplied connectors.

8. Install the barrel connector on the power supply into the connection

labeled 12V standby battery.

9. Plug the DC power supply into a standard outlet.

1. Program the Auto Dialer according to the United Security

Products Model AVD-45b Automatic Voice Dialer instruction

manual.

2. Be sure to note if normally open or normally closed contacts are

used to trigger the Auto Dialer. This will have to be programmed

into the Auto Dialer.

1. When programming for pagers, call the desired pager from the

telephone number and telephone line that the Auto Dialer will be

attached to. Record the time required for the pager service to

answer. Use that time for programming the required number of

pauses needed. Each pause is two seconds in length.

2. If a cell phone does not ring before the Auto Dialer hangs up,

program the cell phone number into the Auto Dialer with pauses

after the number. Note: The number of pauses will depend on each

cell phone and must be tested.

3. If a delay is desired before the Auto Dialer calls out to help prevent

nuisance calls, set the entry delay to "on" and the channel to

"continuous" mode. This will require that channel activation to be

tripped for 20 seconds before dialing out and remain activated

throughout the dialing process.

1. All people or organizations should be notified that the auto dialer

will be calling and the action you would like them to take.

2. Apply power to the unit.

3. Be sure an active telephone line and all wiring is connected to the

auto dialer.

4. Press the "M" key until "Operate" appears in the LCD.

5. Trigger the signaling device to cause the auto dialer to call out.

6. The auto dialer will dial the numbers stored in locations 1-4. The

out going message will be delivered when the auto dialer receives

an answer. For pager numbers, the pager code will be transmitted

instead of the outgoing message.

7. The auto dialer is now ready for operation.

8. Test the Auto Dialer system once a month to insure the outgoing

message is being sent and received.

For detailed specifications on this product, or for the complete line of SJE-Rhombus

panel, alarm, and switch products, visit our web site at www.sjerhombus.com.

Note: The Auto Dialer AVD-45b will attempt to deliver the outgoing message twice with a maximum of 10 attempts for each telephone number.

Note: This device should not be used for life saving applications.

1 2

Komentarze do niniejszej Instrukcji

Brak uwag

United Security Products AVD-45c Dokumentacja Strona 2

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Domofony United Security Products AVD-45c